The 49 Hudson Project

By -
The Hudson was going to be a project car that would only require some body repair, rebuild engine and transmission and fix the existing modifications. It turned in to a complete dismantle and rebuild.
The car is now apart and mounted on the rotisserie.
 Fire wall will be cleaned up, repaired and holes filled.
 The dash has been completely removed along with the steering and brake assembly's. The wiring is not repairable so the car will be rewired.
 The right and left front floor pans are cut out and new one's will be installed.

center floor pan removed and both sides cut out.

 The trunk floor pan and gas tank will be replaced.
 The next three pictures show the rear leaf spring front mount that has broken away from the frame and damaged both ends of the spring.


 Well here we go with a lot of work. It is to bad that the guy that did all this lousy work on the car did not do it right at the time the modifications were made. Also the front frame clip ,engine and transmission were transplanted from a 1970 Chrysler that are completely worn out.

Comments

Post a Comment

Popular posts from this blog

By -
Image
  CHOPPED 51 FOR SALE By  Ron's Hot Rods   -  August 19, 2019 We are considering selling our very special 51 Ford 4 door that has been heavily modified.  We have won multiple awards including Grand National Radical Hardtop 2nd place and Sacramento Autorama Radical Hardtop 1st place.  All information regarding complete build and description available upon request.  Contact Ron Austin via email:  austinpeakrd@gmail.com or comments in blog post. Paint - Sky Blue with Sunset Flames, Custom designed flames with pin stripping, Top chopped 3", lengthened 4", rain gutters removed, Hood peaked & louvered, Nosed, decked, door handles & side trim removed, seams filled, Gas filler relocated, Headlights frenched, Fire wall & inner finders filled and smoothed, Bumpers filled, One piece front & back glass custom made, Custom made rear & trunk floor pans, Bottom of car finished and painted, Hand formed interior trunk panels, One piece door gla...
Read more

RV shelter mezzine extension and inclouser

By -
Image
 I guess I was on a roll after the solar project as I continued to look for an additional project to use up some of the materials that has been collected over the years. The largest being the 4'X8' & 4'X10' AIRLIGHT building panels from Wanessa-Sue Inc. that are the same construction as the ones used for the caboose project, posted a few years ago.  The RV Shelter is completely home made from 2' heavy wall conduit for posts and trusses, 2x4's, and Home Depot metal siding and roof panels. The side and end wall have been insulated with 5 1/2" panels that were free from Wanessa-Sue as they were flawed and not sellable. The existing mezzine is 20' wide by 8' deep built in 2007 that has been used for storage and car restoration projects. The concrete slab is 20' X 10' and we were going to extend it 20' but decided the cost was too much. A Laser level was used to get the elevation level correct for the 10'exrension to the next 2' p...
Read more

Solar Project

By -
Image
Our existing solar system is 20 years old and needed to be updated. I contacted Wind and Solar (NAZ Solar) in Flagstaff for advice and cost for a new system and they recommended a Hybrid Sol-Ark inverter with 400-watt solar panels and had all components in stock. We ordered the new system, and I started taking the old one down. Existing main panel with solar disconnect. Old solar panels. Existing 3000 watt inverter. Next 3 is the existing 20 year old panels. Existing 18 panels are 175 watt. It took 2 weeks to take the existing system down and to receive the new components. New 18–400-watt panels are 5' 8' tall and 3' 8' wide and too large for me to handle myself. My son and 2 of my grandsons came from California over the weekend to put the new panels in place. New Sol-Ark 15K inverter and battery system. Below is the existing support system that was reused. Hope this new system will last another 20 years.
Read more